Final Project
The final project for ELEC 3030 requires some improvement made to my radio. Together with my partner, Farris Hejazen, we intend to develop our radio on a printed circuit board (PCB) that includes an auxiliary input and Bluetooth capability. We designed our circuit using the software, Eagle, and sent our schematic to a third party website, JLCPCB, to have it printed. Once we got those board I soldered on our components to compose our radio. The most pressing issue we had was finding a suitable Bluetooth audio receiver that we could incorporate into our radio.

Figure 1: First draft of final radio
Above is the circuit schematic for the original plan for our final radio. The Schematic was made in LTSpice and has the output signals of each stage of the radio. We broke our final project into three stages: the PCB, the auxiliary input, and the Bluetooth input. Ours goals were to complete one stage before moving to the next so that no matter how much work we were able to get done; we were still able to complete some portion. Our first task was to convert the radio schematic above to a printed circuit board.

Figure 2: Final PCB design
When we converted our radio design to PCB we realized that we could simplify our circuit by changing our audio amplifier. We decided to change from the OP amp to the LM386 because the LM386 only required a single voltage source opposed to the OP amp that required a positive and negative Vcc. The figure above shows our final design for our PCB, it contains the LM386. Another problem we encountered while developing the PCB was that the components R5, R10, and C3 would be connected to ground on both sides when we tried to ground them. To solve this problem we added a pseudo component that was named R4R6C5GND (the name of the component is inaccurate and should be called R5R10C3GND). The purpose of this pseudo component is to provide open pins to ground which allowed us to ground components R5, R10, and C3 which we were previously unable to. After making the decision to add a separate component and then constructing it, I realized that the back of the PCB was a grounding plate and we needed to simply connect the components to this ground plate to ground them.

Figure 3: FInal circuit schematic for the PCB including the Audio amp change to an LM386
For the second and third stage of our final project we intended to add two new input signals from an auxiliary input and a Bluetooth input. After determining that we received sinusoidal signals from both new inputs we realized that we could feed these new inputs directly into the audio amplifier stage of our radio. We knew that we would have three signals trying to be fed through the audio amplifier so we added a three-toggle switch that would determine which input signal would be transmitted to the amp. The switch was initially configured to have the three positions: OFF, ON, ON, but I determined that the OFF position was made by creating an open circuit in the switch. I connected one of our three input signals to the open circuit of the OFF position, and then we had a three-toggle switch that had positions: ON, ON, ON. Since we reconfigured the switch, we were able to connect each of our three inputs and toggle between them and have three potential states for use in our radio.
Of the three input signals, we create the radio signal with our antenna but, the auxiliary input is taken from a female 3.5mm headphone jack. The 3.5mm headphone jack works by breaking the connections it makes into multiple rings. There are 3 configurations of the headphone jack including: 2, 3, and 4 ring configurations. Each ring has a unique purpose, but in all configurations there is an input audio signal on the lowest ring and a ground on the top ring. To take advantage of the similarities between all configurations we used only the input signal received from the bottom ring which in the 3 and 4 ring configurations is the left side audio input. While this signal is only part of the audio, we believed it to be sufficient for users of our device because mixing the right and left hand signals was beyond the scope of our project. Figure 4 below shows an example waveform of the output of our auxiliary input.

Figure 4: Example received waveform from the auxiliary input
The third and final stage of our final project was getting Bluetooth functionality. Our goal was to find a Bluetooth audio receiver that we would be able to incorporate into our circuit as the final input signal. However, we couldn't find an adequate Bluetooth module so we were forced to go out and re-purpose some Bluetooth device. Farris took apart a Bluetooth speaker and I found some cheap Bluetooth headphones. Both components were sufficient and were able to play a received signal. Below in figure 5 is an image of an example waveform from the Bluetooth receiver.

Figure 5: Example received waveform from the Bluetooth input.
The combination of all three input signals worked as we planned with our three-toggle switch. However, our final project did not. We determined that the reason our project did not work was because of our audio amplifier. The signals we received from the different inputs were all clear strong signals, but after feeding them through our audio amplifier, the output of the speaker was nothing like what we were expecting. The output was especially noise and not much louder that the initial signal that was received from each input. We were unable to determine why the audio amplifier was not performing as expected, but we believe that it is because of a poor connection in our PCB. The output signal occasionally sounds like the expected input and because of this we feel that the audio amplifier has some weak connection that is creating all the noise.
Conclusion
Upon completing the class ELEC 3030 I learned about all the basic components necessary to build a simple AM radio. I was able to learn about multiple designs for each component, and I learned how to chose which components work best with one another to create the strongest radio. During my time on my final project I learned even more about basic audio transmission. Specifically the types of signals that are received and how to improve them to drive a speaker. I also learned about the basics of PCB design and construction. I was able to learn how to use the design software Eagle and also learn about the ways to improve the design of the PCB so that it is as efficient as possible.